|
AVAILABLE USED SCREENING/CRUSHING PLANT
Simplicity 7’ x 20’ TD Screen & 66” El-Jay Rollercone Crusher
Conveyor
under 66" Rollercone is 60" X 32' Dodge TXT 4 and 10 HP.
Conveyor
under screen is 48" X 27'6" Dodge TXT 5 and 15 HP.
On plant
side discharge conveyor is 24" with Dodge TXT 3 and 5 HP.
Short
screen to Crusher conveyor is 60" X 5'6" Dodge TXT 4 with 5 HP.
66"
Cedar Rapids/El Jay (S/N 60054) Cone Crusher with 300
HP 1200 rpm Electric Motor
7 X 20,
3 deck, Simplicity (S/N 3720-LP160A-1797), single shaft, screen with 60
HP, 1800 rpm,
electric drive (Bottom deck is not being used). Oil lube with separate
reservoir and pump.
Feed Height to Simplicity is approximately 18'.
Dings
Magnet is 36" X 10', Model 330MH, with a TXT 4 reducer and 10 HP
(NOT
INCLUDED)
Screen
Feed Conveyor
(NOT
INCLUDED)
Off
Plant, Close Circuit conveyor between is an 36" X 32' channel frame.
(NOT INCLUDED)
Electrical: Three
cabinets and the stop start controller.
Existing
Conveyor Belts, Pulleys, Simplicity Screen and Rollercone are all
operating fine.
This
plant has some new bearings and wing tail pulleys that have been
replaced as needed.
Overall
this plant appears to be in “Good” condition and, currently, remains in
operation.
66" Cone
and the Simplicity Screen are mounted on a 20" Beam that sits on
a concrete structure.
Current
“Owner” has Axles that could be borrowed to move this equipment.
$179,900
|
|
AVAILABLE
USED “IMPACTOR” RECYCLE SYSTEM
Portable Recycle
System of “Grasan Plant Design” featuring Hazemag, Model APPH
1515, Impactor powered by a
Cummins QSK 19 Diesel, quad axle system and under impactor pan feeder of
63” wide by 82” long including Seco VGF of 5’ x 20’ with 5’ grizzly set
at 2 1/4” opening. Portable Screening Plant with Cedarapids 7’ x 20’,
triple deck, screen, (54”) plant feed conveyor, three (30”) plant cross
conveyors, 60” x 53’ fines discharge conveyor with all mounted off
tri-axle frame. Portable 48” x 40’ transfer conveyor including a Dings
electro magnet off single axle with dual tires. Portable power van with
Cummins diesel/generator including Onan 350 Kw and electrical controls.
Plant design incorporates heavy-duty, hydraulic jack legs and hydraulic
folds, as required, for “Quick & Easy” system set-up. Plant Model Year
of 1997 with 1515 Impactor New in 2003.
575,000 |
|
Conveyors : "Photos available upon request"
Conveyor: 30”x60’ Truss Type w/Belting, Motor & Stand “RAC03B-10”
------------------------------------ $8,000
Conveyor: 20”x25’ Channel Frame w/Belting & 3Hp Motor “RAC04B-10”
---------------------------------- $1,000
Conveyor: 18”x60’ Truss Type w/Belting & Motor “RAC05B-10”
-------------------------------------------- $2,250
Conveyor: 24”x30’ Channel Frame w/Belting & Motor “RAC06B-10”
--------------------------------------- $1,500
Portable Conveyor: 24”x40’ 20”Truss w/Belting & Motor “RAC07B-10”
------------------------------------- $3,750
Conveyor: 24”x25’ Channel Frame w/Belting & Motor
“RAC10B-10”--------------------------------------- $1,250
Conveyor: 24”x20’ Channel Frame w/Belting & Motor “RAC11B-10”
--------------------------------------- $1,500
Conveyor: 30”x60’ Truss Type w/Belting & Motor (HF w/Some Truss Damage)
“RAC12B-10” ----------- $2,750
Radial Stacker: 30”x90’ Truss Type w/ Belting & Motor Manual Raise
“RAC13B-10” ----------------------- $8,950
Portable Conveyor: 48”x30’ Channel Frame w/Belting & Motor Manual Raise
“RAC14B-10” -------------- $6,950
Portable Conveyor: 24”x50’ Truss Type w/Belting, Hopper & Motor
“RAC15B-10” ------------------------- $4,750
Portable Conveyor: 24”x80’ Truss Type w/Belting, Hopper, Motor & Manual
Raise “RAC16B-10” -------- $6,250
Portable Conveyor: 24”x80’ Truss Type w/Belting, Hopper, Motor & Manual
Raise “RAC17B-10” -------- $6,250
Portable Conveyor: 24”x80’ Truss Type w/Belting, Hopper, Motor & Manual
Raise “RAC18B-10” -------- $6,250
Portable Conveyor: 24”x80’ Truss Type w/Belting, Hopper, Motor & Manual
Raise “RAC19B-10” -------- $6,250
Portable Conveyor: 30”x90’ Truss Type w/Belting, Hopper, Motor & Manual
Raise “RAC20B-10” -------- $8,750
Portable Conveyor: 24”x80’ Truss Type w/Belting, Hopper, Motor & Manual
Raise “RAC22B-10” -------- $6,250
Portable Conveyor: 24”x80’ Truss Type w/Belting, Hopper, Motor & Manual
Raise “RAC23B-10” -------- $6,250
Radial Stacker: 30”x125’ Truss Type w/ Belting, Motor, Manual Raise &
Hopper “RAC24B-10” ----------- $13,750
Conveyor: 24”x24’ Channel Frame w/Belting & Motor (Bonded) “RAC25B-10”
--------------------------- $1,500
Radial Stacker: 24”x60’ Truss Type w/ Belting, Motor & Manual Raise
(H-F) ”RAC30B-10” ----------------$6,750
Radial Stacker: 24”x60’ Truss Type w/ Belting, Motor & Manual Raise
(H-F) ”RAC31B-10” ----------------$6,750
Portable Radial Stacker: 36”x120’ Truss Type Side Fold w/Belting,
Hopper, 50HP, Belt Scale,
Hyd Raise & Power Radial (H-F) “RAC32B-10”
----------------------------------------------------------- $39,950
Portable Conveyor: 42”x 85’ Truss Type w/Belting, Motor & Manual Raise
(H-F) “RAC33B-10” --------- $19,950
Portable Radial Stacker: 30”x90’ Truss Type w/Belting, Hopper, Motor &
Manual Raise (Kolberg) “RAC34B-10”
---------------------------------------------------------------------
$13,750
Conveyor: 36”x60’ Channel Frame w/Belting, Hopper, Motor & Support (Kolberg)
“RAC35B-10” ------- $2,750
Radial Stacker: 36”x80’ Truss Type w/Belting, 25Hp Motor & Hyd Raise (Kolberg)
“RAC36B-10”--------- $17,500
Conveyor: 42”x 360’ Truss Type w/Belting, 40Hp & Dodge 7
“RAC42B-10”------------------------------ $36,000
Conveyor: 42”x 380’ Truss Type w/Belting, 40Hp & Dodge 7
“RAC43B-10”------------------------------- $37,400
Conveyor: 24”x200’ Truss Type w/ Belting & Motor
“RAC44B-10”------------------------------------------- $6,750
Radial Stacker: 24”x80’ Channel Frame w/ Belting, Motor & Hyd Raise
(End Fold for travel)
“RAC45B-10”-------------------------------------------------------------------------
$8,250
Radial Stacker: 24”x75’ Channel & Truss Frame w/ Belting, Motor & Manual
Raise “RAC46B-10”--------- $7,250
Conveyor: 24”x120’ Truss Type w/ Belting & Motor
“RAC47B-10”------------------------------------------ $7,750
Two (2) 24”x40’ Ship Channel Conveyors w/Belting & Motor “RAC100B-10”
----------------------------- $2,250ea
30”x28’ Truss Type Portable Transfer Conveyor w/5Hp, Dodge 4, single
axle
& 7:00x20 tires “RAC1001B-10”
---------------------------------------------------------------------------
$2,500
30”x60’ Truss Type w/Belt & Motor (HF Transfer & VG Condition)
“RAC102B-10” ----------------------- $5,500
|
